Step-Up Module MT3608
1.Electrical characteristics
1). The maximum output current: 2 a
2). The input voltage: 2 v ~ 24 v
3). The maximum output voltage: 28 v
4). Efficiency: max 93%
2.Mechanical properties
1). product size: 36 mm * 17 mm * 14 mm
3.Method of use
The module of the IN+ and – after 2~24v, IN adjusting the potentiometer can adjust output voltage, output voltage is greater than the input voltage
4.Matters needing attention
1). The input voltage should not exceed the maximum input voltage
2). The peak current output current is no more than TV university
- Beschriftung: MT3608, www.icstation.com, UCSA004A
- Bezugsquelle ebay (ca. 1€)
Step-Up Module SX1308
DC-DC SX1308 booster module carrying SX1308 chip, its packagnig is small, and high efficiency. The output power can be adjust, maximum can arrive 28V and its interior integrate the lowest RDS internal resistance 100m? metal oxide semiconductor field effect transistor (mosfet), which can realize large current output of up to 2A. It widely used in 3G network products, digital products, mobile power supply,battery power supply, equipment, etc.
Functional features:
– Oscillation frequency 1.2MHz
– efficiency is as high as 95%
– Circuit has short circuit protection, overheating protection function
– 10k to adjust potentiometer, adjust the output voltage
Technical parameters:
– Maximum input voltage: DC 2-24V
– Maximum output voltage: DC 2-28V
- keine Beschriftung
- Bezugsquelle ebay (ca. 1,2€)
USB Step-Up Boost Module
- Bezugsquelle ebay
Step-Up 5V booster module
Hersteller Shenzhen LC Technology?
1 On-board subminiature PFM control DC/DC boost controller chip
2 Input 0.9 V ~ 5 V any dc voltage, all can stable output 5 V dc voltage
3 On-board female USB , can supply power to the USB interface equipment directly
4 On-board input voltage indicator
5 PCB size: 34 (mm) x16.2 (mm)
Step-Up 5V booster module
DC / DC boost controller chip onboard ultra-compact PFM control
Enter any DC voltage of 0.9V ~ 5V, can be stable output 5V DC voltage, output current of 500 ~ 600MA with two AA batteries input to a single AA battery-powered output current 200ma so, for the mobile phone, camera , single-chip, digital products supply. Stable output 5V DC voltage
Onboard USB female, can be directly powered USB interface device with USB female versatile
On-board input voltage indicator
PCB size: 34 (mm) x16.2 (mm) ultra-small size, installed in a variety of small equipment
Step-Up Module SY-DC3403
1) Model: SY-DC3403
2) Circuit characteristics:
– ultra-small size: 32x34x20mm.
– input (3.7V ~ 34V), output (3.7V ~ 34V) between any adjustments, the current in the same volume of DC-DC circuit, very few can achieve such a high voltage.
– Maximum input current 3A, 2A current recommended in the following, leaving a certain margin. Power up to 15W or so, up to about 90% efficiency.
Note:
– Use heavy gauge wire to connect the circuit. Clockwise decreases the voltage, the voltage increases counterclockwise.
– positive and negative input and output can not be reversed, the output is not short-circuit.
– The output voltage must be limited to 35V or less, otherwise it will damage the circuit.
– connect the input power, and then adjust the voltage to their needs. Finally, draw a line load!
– As the step-up DC-DC circuit, the input voltage is lower than the output voltage. In order to ensure stable output voltage.
– as close as possible the input and output voltage, input voltage * Input Current efficiency = output voltage * Output current. The closer the input and output voltage output current greater!
3)Note: This can not be used for notebook, laptop at least 60W of power.